Pro-tip: Plaster of Paris can be sanded to a completely smooth finish but be careful not to smooth out your puppy's paw print. If you plan on adding a finish to the cast after sanding it, use a cotton cloth to remove any excess grit beforehand. Using 120-grit or higher sandpaper, smooth the rough spots around the edges.ĭon’t press so hard that you sand off too much. Pro-tip: Fill up a bucket with water for this step, rather than washing the plaster cast beneath running water. To wash, use your fingers as opposed to anything abrasive like a brush or scrubber. Some of the molding compound will still be attached to the paw print cast, but you can rinse it off with water. Pro-tip: Your project isn’t completely set at this time and will need more time to cure fully. Be careful if you want to use the same paw print again. In other words, remove the plaster cast from the plastic cup. De-mold the projectĪfter about an hour, de-mold your project. Scroll down for a few ideas for what to write. Note: Wait until the plaster has clay-like consistency to make your mark. Pro-tip: During the drying stage, you may want to inscribe something in the plaster using a pencil or similar object. Refer back to the instructions on the plaster mix for drying time.ĭrying can take an hour or more, depending on the humidity of your home or climate. » MORE: Are you preparing for the loss of a loved one? Get support now. If you attempt this step at a later time, you will likely damage the mold. Pro-tip: if you would like to hang up the mold once it’s dry and sanded, this is the time to insert a paperclip or other metal hook of sorts. Gently shake or tap the container on your work surface to eliminate any bubbles that may affect the outcome. Pro-tip: A half-inch is not an exact or required measurement of the mix it’s just a recommendation. Scrape the plaster mix into the plastic container with the Play Dough mold.Įyeball about a half-inch of plaster mix. Pro-tip: Plaster of Paris sets quickly, so don’t mix it up until you’re ready. The consistency will be slightly runny, but this is what you want as it’ll give you enough time to work with the mix. Then, measure and add one-half cup of water.Īn old spatula works well for mixing. Measure and add one cup of Plaster of Paris (calcium sulfate hemihydrate). Mix the plasterįor this step, you’ll need to use a glass bowl from your craft or work area. Let your pup know you’re happy with their courageous efforts.Ĭheck their paw to make sure it’s clean, too. Reward your little one with some treats and love. You can start over if you make a mistake or if your pup wiggles too much. Once you feel like you’ve made an impression, lift your puppy's paw and check the mold.ĭon’t worry. Be gentle so as not to hurt their little toes. Place your dog’s paw in the container with the compound and press down to get a good print. Remove the second cup, exposing the clean, flat surface of the modeling compound in the bottom of the first cup. Press down firmly on the disc to ensure the compound will remain in place for the next step. Next, using a slightly smaller plastic cup with its bottom side down, insert it into the larger one holding the modeling compound. Using your fingers, lightly press the disc, flat side down, into the repurposed plastic container. Use one the size and depth of a shredded parmesan cup or about four inches. Press disc flat into a containerįor this step, repurpose a (clean) flat-bottomed plastic food container. Flip over the disc and roll it out from both sides. Then, using a bottle as a rolling pin to flatten the ball to form a disc shape. Next, form a ball from the two containers of Play Dough (or from your mixture) by rolling them in your palms.
However, if you want to make your modeling compound for less than $1.00, check out this i heart naptime blog post. Pro-tip: Most big-name box stores will have a ready supply. You’ll need two containers of Play Dough for this project. Pencil, if writing in the mold while it’s drying.Two containers of store-bought modeling compound, unless you make your own.Making a dog paw print from plaster is super easy and doesn’t require a lot of material or time. Steps for Making a Dog Paw Print in Plaster » MORE: Our members can save an average of $1000 when funeral planning.
0 kommentar(er)
